spL Performer S800 Power Amplifier

Price$4,869.00
Savings$1,374.00
Special Price $3,495.00 CAD
BRAND NEW
Payment Options :  
Availability In Stock905-503-0850

New unit available in silver finish. 1-833-527-3336.

 

 

With a power amplification of 2 x 285 W (4 Ω) [2 x 185 W (8 Ω)] or 1 x 450 W (8 Ω, Bridge Mode), this amplifier easily controls any loudspeaker. Thanks to VOLTAiR technology, it is fast, precise and highly efficient with outstanding sound.

 

The Performer s800 has a protection circuit against DC voltage and against overheating. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red.

To protect the s800 against the unlikely event of overheating, a temperature sensor at the heatsinks continously monitors the temperature of the device. The TEMP LED lights up yellow when the Performer s800 is getting too hot.

As a result of this the output stage is switched off and the fans run on high-speed until the device has cooled down.

“Dynamically, the Performer s800 hangs excellently on the gas, shows itself to be very confident and tidy, and maintains its clean, unstrained midrange/treble reproduction even at higher levels. The razor-sharp focus in terms of spatial imaging is also impressive.” - Holger Biermann (LowBeats)

 

Trim to fit

With reference to the Performer s800, “fit” means adapted.

You can adapt the input sensitivity in 0.5 dB steps from 0 dB to -5.5 dB. In contrast to a panorama potentiometer in a preamplifier, this trim switch is the more audiophile solution.

In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode.

The VOLTAiR Technology

The 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.

Specifications

Analog Input & Thru: XLR (balanced)

Input impedance (THRU not connected) 20 kΩ

Common mode rejection (THRU not connected) -82 dB

Input sensitivity 6 dBu

Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug

Output power (RMS, 4 Ω) 2 x 285 W

Output power (RMS, 8 Ω) 2 x 185 W

Harmonic distortion (1 kHz, 8 Ω) < 0.03 %

Output power (RMS, 8 Ω, Bridge Mode) 450 W

Harmonic distortion (1 kHz, 8 Ω, Bridge Mode) < 0.011 %

Output voltage (peak to peak) 74 V

Output voltage (peak to peak, Bridge Mode) 180 V

Output voltage (RMS) 35 V

Output voltage (RMS, Bridge Mode) 86 V

Output impedance (20 Hz – 20 kHz) < 0.031 Ω

Output impedance (20 Hz – 20 kHz, Bridge Mode) < 0.043 Ω

Amplification gain 26 dB

Amplification gain (Bridge Mode) 32 dB

Damping factor (1 kHz, 8 Ohm) > 300

Damping factor (1 kHz, 8 Ohm, Bridge Mode) > 190

Frequency range (-3dB) 10 Hz – 80 kHz

Noise (A-weighted) -123 dBu

Internal Linear Power Supply with Shielded Toroidal Transformer

Toroidal transformer 875 VA

Operating voltage (Input stage) +/- 60 V

Operating voltage (power stage) +/- 60 V

Operating voltage for relays, LEDs, AMP CTL + 12 V

Mains Power Supply

Mains voltage (selectable, see fuse chamber) 230 V AC / 50; 115 V AC / 60 Hz

Fuse 230 V T 4 A

Fuse 115 V T 8 A

Power consumption max. 875 VA

Idle power consumption 40 W

Stand-by power consumption < 0.3 W

Dimensions & Weight

W x H x D (width x height incl. feet x depth) 278 x 100 x 342 mm (11 x 4 x 13.5 inch)

Unit weight 12.8 kg (28.2 lbs)

Shipping weight 14 kg (30.9 lbs)

Write a review